APCOTHANE CF 678 / APCOTHANE 678

PRODUCT DATA SHEET 

---

TECHNICAL DATA

Property	Value
Colour Range	Available in various shades
Gloss	Glossy
Volume Solids	Approx. 57%
Recommended DFT / Coat	50 – 75 µm
Theoretical Coverage Capacity	11.40 m²/l @ 50 µm 7.60 m²/l @ 75 µm
Drying Time at 30°C	Surface Dry: 90 min Hard Dry: 6 hrs Full Cure: 7 days
Overcoating Interval at 30°C	Min: 6 hrs Max: Unlimited (provided surface is clean)
Method of Application	Air Spray / Airless Spray

Note: Data are guidelines only. Actual values depend on film thickness, ventilation, humidity, and temperature (30°C & 65% RH).

---

DIRECTIONS FOR USE

Surface Preparation

General

• Surfaces must be dry, clean, and free from contaminants.
• Remove dirt, dust, oil, grease per SSPC-SP1 solvent cleaning.
• Surface should be checked and treated as per ISO 8504 before priming.

Primed Surfaces

• Suitable epoxy primer or epoxy/polyurethane undercoat should be dry and contamination-free.
• Apply Apcothane CF 678 / Apcothane 678 within the specified overcoating interval of the primer/undercoat.
• For aged epoxy coatings, roughen the surface before painting.

---

Application Conditions

• Substrate temperature ≥3°C above dew point, ≤50°C.
• Relative humidity ≤85%.
• Ensure good ventilation in confined areas for proper curing.

---

Mixing

Parameter	Specification
Mixing Ratio (by volume)	Base : Hardener = 5 : 1
Induction Time	15 minutes
Pot Life @ 30°C	2 hours

• Stir base and hardener separately.
• If settled, loosen with a hand stirrer, then mix thoroughly with a mechanical stirrer.
• Add hardener gradually under continuous stirring.
• Avoid part mixing; if done, close lids tightly to prevent moisture ingress.
• Add thinner after mixing and induction time.
• Over-thinning reduces sag resistance.

---

Application Methods

Method	Recommended Thinner	Volume of Thinner	Nozzle Orifice	Nozzle Pressure
Brush / Roller	T-213	0 – 10%	–	–
Air Spray	T-213	15 – 45%	1.5 – 3.0 mm	0.3 – 0.4 MPa (3–4 atm; 43–57 psi)
Airless Spray	T-213	5 – 15%	0.28 – 0.33 mm	10 – 13 MPa (100–130 atm; 1400–1800 psi)

Note: Depending on film thickness & conditions.

---

Cleaning

• Do not allow paint to remain in hoses, guns, or spray equipment.
• Clean all equipment immediately with Thinner T-213.
• Periodically flush spray equipment during the day.
• Dispose of surplus material and containers per local regulations.

---

PRODUCT CHARACTERISTICS

• Dry film thickness by brush: 40–50 µm/coat; by spray: 50–75 µm/coat.
• For red/yellow/orange shades, two coats may be required for hiding on dark undercoats.
• Excessive thickness delays drying.
• Gloss and finish depend on application method.
• Pastel shades (white, yellow, red tones) require at least two coats for full opacity.
• Always use only the recommended thinner; alternate thinners affect curing.
• Premature condensation or rain may cause colour/gloss changes.

---

OVERCOATING & TOPCOATS

• Can be top-coated on most epoxy and polyurethane primers/undercoats as recommended by Asian Paints PPG representatives.

---

PACK SIZE

• 20 L (Base: 16.77 L + Hardener: 3.33 L)

---

STORAGE

• Shelf Life: Minimum 9 months @ 30°C in original unopened pack.
• Store in cool, dry place as per local regulations.

---

REGULATORY INFORMATION

Property	Value
Flash Point	Base ≥24°C, Hardener ≥24°C
VOC	380 – 410 g/l (as per US EPA Method 24)
Product Weight	1.02 – 1.17 kg/l (depending on shade)

 

---

SAFETY INFORMATION

• Avoid inhalation of vapours or paint mist, and contact with skin/eyes.
• Provide forced ventilation in confined spaces.
• Even with ventilation, use respiratory, skin, and eye protection while spraying.
• Refer to Material Safety Data Sheet (MSDS) prior to use.

---

References

Product Data Sheet – APCOTHANE CF 678 / APCOTHANE 678
Issued by Asian Paints PPG Pvt. Ltd. – July 2024 (Revision: September 2019)
Document Version: PC 2585
Source: https://www.asianpaintsppg.com

Technical Guidelines and Explanatory Notes
Last accessed: 28 May 2025
Reference link: https://www.asianpaintsppg.com/service-support/technical-guidelines

Note: Always consult the latest version of the Product Data Sheet and associated documents directly from Asian Paints PPG’s official website to ensure accuracy and compliance with the most current recommendations.