APCODUR CF 699

PRODUCT DATASHEET

---

TECHNICAL DATA

• Colour: Off White and Greys
• Gloss: Eggshell
• Volume Solids: Approx. 60%
• Recommended DFT/Coat: 75 – 125 µm
• Theoretical Coverage Capacity:
  • 8.0 m²/l at 75 µm DFT
  • 4.8 m²/l at 125 µm DFT
• Drying time at 30°C:
  • Surface Dry: 2 hours
  • Hard Dry: 12 hours
  • Full cure: 7 days
• Overcoating interval at 30°C:
  • Minimum: 12 hours
  • Maximum: 5 days (if surface is dry and clean)

Data are guidelines only. Drying/overcoat interval depends on film thickness, ventilation, humidity, temperature. Values given are at 30°C and 65% RH.

---

DIRECTIONS FOR USE

Surface Preparation

General

• Can be applied directly over blasted steel substrate
• Suitable epoxy primer: Apcodur CP 689 / Apcodur CP 682 (dry, contamination-free)
• If recoating exceeds 5 days, surface must be roughened and cleaned prior to painting
• Surfaces must be dry, clean, free from dust/oil/grease (remove oil/grease per SSPC-SP1)
• Treat surface as per ISO 8504 before priming
• Remove weld spatter, seams, and sharp edges

Blast Cleaning

• Steel: Abrasive blast clean min. Sa 2.5 (Swedish)
• If oxidation occurs after blasting, re-blast
• Recommended blasting profile (Rz): 50–75 µm
• Correct/treat any defects revealed by blasting

New Concrete Surface

• Cure minimum 3 months
• For severe exposure: light blasting preferred
• Where blasting impractical: wire brushing + treat with 10% HCl acid
• Wash thoroughly to remove acid and contaminants
• Allow to dry before primer

Old Concrete Surface

• Remove grease/oil with solvent or 10% caustic solution
• Preferably light blasting, or else etch with 10% HCl acid
• Wash thoroughly, ensure joints do not retain acid
• Dry surface completely before primer

Note: Surface must be thoroughly dried before primer to ensure performance.

---

Application Conditions

• Substrate temperature ≥3°C above dew point and ≤50°C
• Relative humidity <85%
• Good ventilation required in confined areas

---

Instruction for Use

• Supplied in 2 packs (base + hardener). Stir both separately.
• If settling seen, stir manually then mechanically at low RPM.
• Add hardener gradually into base under continuous stirring.
• Consume mixed product within pot life.
• Avoid part mixing; if done, reseal tightly.
• Excess thinner reduces sag resistance.

Mixing Ratio (by volume): Base:Hardener = 4:1
Induction Time: 15 minutes
Pot Life at 30°C: 3 hours

---

Application Methods

Airless Spray

• Thinner: T-141
• Volume: 5–20% (depending on thickness/conditions)
• Nozzle: 0.43–0.58 mm (17–23 thou)
• Pressure: 20–24 MPa (200–240 atm; 2800–3400 psi)
• Cleaning Thinner: T-141

Brush/Roller

• For stripe coating/small areas only
• Thinner: T-141
• Cleaning: T-141

Notes:

• For single feed airless, use pump ratio 68:1
• Clean equipment immediately after use with Thinner T-141
• Periodic flushing of spray equipment recommended

---

PRODUCT CHARACTERISTICS

• Full cure required before service exposure
• Product discolours on sunlight/immersion, performance unaffected
• Adjust application parameters at site as per conditions
• In confined tanks, control RH using dehumidifiers
• Premature exposure to ponding water may cause colour change
• Stripe coat required on welds/edges before full coat
• Consult Asian Paints PPG technical representative for system recommendation

---

PACK SIZE

• 20 L (Base: 16 L + Hardener: 4 L)

---

STORAGE

• Shelf life: ≥12 months at 30°C (sealed pack, inspect thereafter)
• Store in cool, dry conditions as per regulations

---

REGULATORY INFORMATION

• Flash point: ≥24°C (Base & Hardener)
• VOC: ~390 ± 20 g/l (per US EPA Method 24)
• Product Weight: ~1.36 ± 0.05 kg/l

---

SAFETY INFORMATION

• Avoid inhalation of vapours/paint mist and contact with skin/eyes
• Forced ventilation required in confined/stagnant spaces
• Respiratory, skin and eye protection recommended during spray
• Refer to Material Safety Data Sheet (MSDS) before us

References

Product Data Sheet – APCODUR CF 699
Issued by Asian Paints PPG Pvt. Ltd. – July 2024 (Revision: Sept 2019)
Document Version: PC 0455
Source: https://www.asianpaintsppg.com

Technical Guidelines and Explanatory Notes
Last accessed: 28 May 2025
Reference link: https://www.asianpaintsppg.com/service-support/technical-guidelines

Note: Always consult the latest version of the Product Data Sheet and associated documents directly from Asian Paints PPG’s official website to ensure accuracy and compliance with the most current recommendations.